test01
This commit is contained in:
@@ -1,399 +0,0 @@
|
||||
# 04.静态路由
|
||||
|
||||
## 1. 静态路由
|
||||
|
||||
- 在少量网段并且相对固定的时候可以使用静态路由
|
||||
- 临时测试的时候
|
||||
|
||||
## 2. 实验
|
||||
|
||||
|
||||
|
||||
### 2.1 配置IP地址
|
||||
|
||||
```
|
||||
R1
|
||||
en
|
||||
conf t
|
||||
int e0/0
|
||||
ip add 192.168.12.1 255.255.255.0
|
||||
no sh
|
||||
end
|
||||
============================
|
||||
R2
|
||||
en
|
||||
conf t
|
||||
int e0/0
|
||||
ip add 192.168.12.2 255.255.255.0
|
||||
no sh
|
||||
int e0/1
|
||||
ip add 192.168.23.2 255.255.255.0
|
||||
no sh
|
||||
end
|
||||
=============================
|
||||
R3
|
||||
en
|
||||
conf t
|
||||
int e0/0
|
||||
ip add 192.168.23.3 255.255.255.0
|
||||
no sh
|
||||
end
|
||||
```
|
||||
|
||||
在R2上可以检查到R1或者R3的连通性，确保IP地址配置正确
|
||||
|
||||
```
|
||||
R2#ping 192.168.12.1
|
||||
Type escape sequence to abort.
|
||||
Sending 5, 100-byte ICMP Echos to 192.168.12.1, timeout is 2 seconds:
|
||||
.!!!!
|
||||
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/3/5 ms
|
||||
R2#ping 192.168.23.3
|
||||
Type escape sequence to abort.
|
||||
Sending 5, 100-byte ICMP Echos to 192.168.23.3, timeout is 2 seconds:
|
||||
.!!!!
|
||||
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/2 ms
|
||||
```
|
||||
|
||||
如果IP地址配置不正确，出现了问题，可以再每台设备上使用如下命令检查
|
||||
|
||||
```
|
||||
R2#show ip int br
|
||||
Interface IP-Address OK? Method Status Protocol
|
||||
Ethernet0/0 192.168.12.2 YES manual up up
|
||||
Ethernet0/1 192.168.23.2 YES manual up up
|
||||
Ethernet0/2 unassigned YES unset administratively down down
|
||||
Ethernet0/3 unassigned YES unset administratively down down
|
||||
```
|
||||
|
||||
### 2.2 检查R1和R3的联通性
|
||||
|
||||
```
|
||||
R1#ping 192.168.23.3
|
||||
Type escape sequence to abort.
|
||||
Sending 5, 100-byte ICMP Echos to 192.168.23.3, timeout is 2 seconds:
|
||||
.....
|
||||
Success rate is 0 percent (0/5)
|
||||
```
|
||||
|
||||
检查R1的路由表
|
||||
|
||||
```
|
||||
R1#show ip route
|
||||
192.168.12.0/24 is variably subnetted, 2 subnets, 2 masks
|
||||
C 192.168.12.0/24 is directly connected, Ethernet0/0
|
||||
L 192.168.12.1/32 is directly connected, Ethernet0/0
|
||||
```
|
||||
|
||||
发现`192.168.23.3`没有匹配条目
|
||||
|
||||
在R1上加上静态路由，告知R1如果想去往`192.168.23.0/24`需要从e0/0接口发出
|
||||
|
||||
```
|
||||
R1(config)#ip route 192.168.23.0 255.255.255.0 e0/0
|
||||
```
|
||||
|
||||
然而还是不通，因为R3并没有返回`192.168.12.0/24`的路由，导致R3只能收到R1的消息，但是不能回复
|
||||
|
||||
```
|
||||
R3(config)#ip route 192.168.12.0 255.255.255.0 e0/0
|
||||
```
|
||||
|
||||
现在三台路由器都知道了`192.168.12.0/24`和`192.168.23.0/24`两个网段的去法
|
||||
|
||||
```
|
||||
R1#ping 192.168.23.3
|
||||
Type escape sequence to abort.
|
||||
Sending 5, 100-byte ICMP Echos to 192.168.23.3, timeout is 2 seconds:
|
||||
..!!!
|
||||
Success rate is 60 percent (3/5), round-trip min/avg/max = 1/1/1 ms
|
||||
```
|
||||
|
||||
### 2.3 ARP在这个过程中
|
||||
|
||||
通过检查R1的arp表，我们可以发现`192.168.23.3`的arp结果和`192.168.12.2`的一样
|
||||
|
||||
```
|
||||
R1#show arp
|
||||
Protocol Address Age (min) Hardware Addr Type Interface
|
||||
Internet 192.168.12.1 - aabb.cc00.1000 ARPA Ethernet0/0
|
||||
Internet 192.168.12.2 5 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
Internet 192.168.23.3 0 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
```
|
||||
|
||||
上面这种情况是代理ARP产生的，如果R1并不是去往R3，而是作为局域网连接外网网关，那么访问的目的地址可能无数个。这种情况下，会导致ARP结果越来越多，影响效率。
|
||||
|
||||
```
|
||||
R1(config)#ip route 0.0.0.0 0.0.0.0 e0/0 # 在R1配置默认路由，模拟R1的e0/0接口是外网
|
||||
R1#ping 192.168.23.4
|
||||
Type escape sequence to abort.
|
||||
Sending 5, 100-byte ICMP Echos to 192.168.23.4, timeout is 2 seconds:
|
||||
..
|
||||
Success rate is 0 percent (0/2)
|
||||
R1#show arp
|
||||
Protocol Address Age (min) Hardware Addr Type Interface
|
||||
Internet 123.123.123.123 0 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
Internet 192.168.12.1 - aabb.cc00.1000 ARPA Ethernet0/0
|
||||
Internet 192.168.12.2 9 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
Internet 192.168.23.3 4 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
Internet 192.168.23.4 0 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
```
|
||||
|
||||
发现不管去往什么地址，都会导致ARP表多出一条。
|
||||
|
||||
检查路由表
|
||||
|
||||
```
|
||||
R1#show ip route
|
||||
S* 0.0.0.0/0 is directly connected, Ethernet0/0 # 发现默认路由条目一次查找，就知道出口了
|
||||
192.168.12.0/24 is variably subnetted, 2 subnets, 2 masks
|
||||
C 192.168.12.0/24 is directly connected, Ethernet0/0
|
||||
L 192.168.12.1/32 is directly connected, Ethernet0/0
|
||||
S 192.168.23.0/24 is directly connected, Ethernet0/0
|
||||
```
|
||||
|
||||
如果数据目的IP地址在路由表中直接能找到出接口，就回直接封装然后转发，如果没有MAC地址的记录，就会触发ARP。
|
||||
|
||||
如果静态路由尝试用下一跳IP地址作为出站线索，触发路由表递归查询
|
||||
|
||||
```
|
||||
R1(config)#ip route 192.168.23.0 255.255.255.0 192.168.12.2
|
||||
R1#sh ip route
|
||||
192.168.12.0/24 is variably subnetted, 2 subnets, 2 masks
|
||||
C 192.168.12.0/24 is directly connected, Ethernet0/0
|
||||
L 192.168.12.1/32 is directly connected, Ethernet0/0
|
||||
S 192.168.23.0/24 [1/0] via 192.168.12.2
|
||||
R1#ping 192.168.23.3
|
||||
Type escape sequence to abort.
|
||||
Sending 5, 100-byte ICMP Echos to 192.168.23.3, timeout is 2 seconds:
|
||||
!!!!!
|
||||
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
|
||||
R1#sh arp
|
||||
Protocol Address Age (min) Hardware Addr Type Interface
|
||||
Internet 192.168.12.1 - aabb.cc00.1000 ARPA Ethernet0/0
|
||||
Internet 192.168.12.2 0 aabb.cc00.2000 ARPA Ethernet0/0
|
||||
```
|
||||
|
||||
如果静态路由配置下一跳的IP地址作为出站线索，那么就会触发路由表递归查找，而最终不仅仅是找到了出口信息，同时还找到了下一跳IP地址的MAC地址，直接会被拿来作为数据链路层的目的MAC地址。
|
||||
|
||||
### 2.4 结论
|
||||
|
||||
在配置静态路由的时候，尽量配置下一跳IP地址作为出口，这样可以避免ARP表的增大。
|
||||
|
||||
## 3. 路由汇总
|
||||
|
||||
为了测试，在R1上配置多个loopback接口，用于模拟多个网段
|
||||
|
||||
```
|
||||
R1#sh ip int br
|
||||
Interface IP-Address OK? Method Status Protocol
|
||||
Ethernet0/0 192.168.12.1 YES manual up up
|
||||
Ethernet0/1 unassigned YES unset administratively down down
|
||||
Ethernet0/2 unassigned YES unset administratively down down
|
||||
Ethernet0/3 unassigned YES unset administratively down down
|
||||
Loopback1 172.16.1.1 YES manual up up
|
||||
Loopback2 172.16.2.1 YES manual up up
|
||||
Loopback3 172.16.3.1 YES manual up up
|
||||
```
|
||||
|
||||
这些地址配置的都是/24,但是我们发现前16位都是一样的，那么R2上可以写如下的汇总静态路由
|
||||
|
||||
```
|
||||
R2(config)#ip route 172.16.0.0 255.255.0.0 192.168.12.1
|
||||
```
|
||||
|
||||
汇总路由可以精简路由条目，加快了查找效率
|
||||
|
||||
但是汇总路由也会导致明细的丢失，造成不必要的路由转发
|
||||
|
||||
## 4. 路由器的配置保存与查看
|
||||
|
||||
当上面的实验做完了，检查网络状态都可以，就可以保存配置了
|
||||
|
||||
```
|
||||
R1#copy running-config startup-config # 把内存中的配置文件，保存到开机启动配置文件中
|
||||
R1#write
|
||||
```
|
||||
|
||||
在配置的时候，可以查看当前的配置文件
|
||||
|
||||
```
|
||||
R1#show running-config # 然后按空格翻页，按q退出
|
||||
R1#show run int e0/0 # 查看接口e0/0下的配置
|
||||
R1#show running-config | section ip route # 查看有ip route的那一行配置
|
||||
```
|
||||
|
||||
正常情况下，`ping`,`show`,`write`等命令只能在特权模式下(#)或者用户模式下(>)使用，如果想在各种配置模式中使用这些命令，可以在命令前面加个`do`来调用
|
||||
|
||||
```
|
||||
R1(config)#show ip route
|
||||
^
|
||||
% Invalid input detected at '^' marker.
|
||||
|
||||
R1(config)#do show ip route # 前面加do可以调用非配置模式下的命令
|
||||
```
|
||||
|
||||
## 5. 管理距离
|
||||
|
||||
当路由器从不同的方式学到了同一条路由条目，由于路由器只能将最佳路由放在路由表中。所以会从多个可用条目中将最佳结果放入路由表。
|
||||
|
||||
路由器使用管理距离去评判路由获得方式优劣。
|
||||
|
||||
|
||||
|
||||
注意！上表是cisco设备的管理距离，每个品牌都会有些不一样，用的时候需要去查一下。
|
||||
|
||||
这个管理距离只是设备自己这么认为，无法影响其他设备，所以必要的时候，我们可以去修改，而不用担心全网的影响。越小越优。不优的不会出现在路由表中。
|
||||
|
||||
```
|
||||
S 192.168.23.0/24 [1/0] via 192.168.12.2
|
||||
# 这个条目中[1/0]里面1是管理距离，是用来判断同一个路由的不同来源的优先级
|
||||
R1#show ip route 192.168.23.0
|
||||
Routing entry for 192.168.23.0/24
|
||||
Known via "static", distance 1, metric 0 # 管理距离是1，度量值是0
|
||||
Routing Descriptor Blocks:
|
||||
* 192.168.12.2
|
||||
Route metric is 0, traffic share count is 1
|
||||
```
|
||||
|
||||
## 6. 浮动静态路由
|
||||
|
||||
浮动静态路由是通过修改管理距离的方式，让静态路由可以做到控制路径，在发生故障的时候，也能切换。
|
||||
|
||||
两个路线都正常的情况下
|
||||
|
||||
|
||||
|
||||
当下面的路线断开之后
|
||||
|
||||
|
||||
|
||||
先配置IP地址
|
||||
|
||||
```
|
||||
R1
|
||||
int e0/0
|
||||
ip add 192.168.12.1 255.255.255.0
|
||||
no sh
|
||||
==========================
|
||||
R2
|
||||
int e0/0
|
||||
ip add 192.168.12.2 255.255.255.0
|
||||
no sh
|
||||
int e0/2
|
||||
ip add 192.168.23.2 255.255.255.0
|
||||
no sh
|
||||
int e0/1
|
||||
ip add 192.168.32.2 255.255.255.0
|
||||
no sh
|
||||
===========================
|
||||
R3
|
||||
int e0/0
|
||||
ip add 192.168.34.3 255.255.255.0
|
||||
no sh
|
||||
int e0/2
|
||||
ip add 192.168.23.3 255.255.255.0
|
||||
no sh
|
||||
int e0/1
|
||||
ip add 192.168.32.3 255.255.255.0
|
||||
no sh
|
||||
==========================
|
||||
R4
|
||||
int e0/0
|
||||
ip add 192.168.34.4 255.255.255.0
|
||||
no sh
|
||||
```
|
||||
|
||||
配置静态路由
|
||||
|
||||
```
|
||||
R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.12.2
|
||||
==================================
|
||||
R2(config)#ip route 192.168.34.0 255.255.255.0 192.168.23.3
|
||||
R2(config)#ip route 192.168.34.0 255.255.255.0 192.168.32.3 2
|
||||
===================================
|
||||
R3(config)#ip route 192.168.12.0 255.255.255.0 192.168.23.2 2
|
||||
R3(config)#ip route 192.168.12.0 255.255.255.0 192.168.32.2
|
||||
==================================
|
||||
R4(config)#ip route 0.0.0.0 0.0.0.0 192.168.34.3
|
||||
```
|
||||
|
||||
检查在线路正常的时候访问的路径
|
||||
|
||||
```
|
||||
R1#traceroute 192.168.34.4
|
||||
Type escape sequence to abort.
|
||||
Tracing the route to 192.168.34.4
|
||||
VRF info: (vrf in name/id, vrf out name/id)
|
||||
1 192.168.12.2 1 msec 0 msec 1 msec
|
||||
2 192.168.23.3 1 msec 1 msec 0 msec
|
||||
3 192.168.34.4 1 msec * 1 msec
|
||||
==========================
|
||||
R4#traceroute 192.168.12.1
|
||||
Type escape sequence to abort.
|
||||
Tracing the route to 192.168.12.1
|
||||
VRF info: (vrf in name/id, vrf out name/id)
|
||||
1 192.168.34.3 0 msec 1 msec 1 msec
|
||||
2 192.168.32.2 0 msec 1 msec 1 msec
|
||||
3 192.168.12.1 0 msec * 3 msec
|
||||
```
|
||||
|
||||
下面关闭R2的e0/2口，来模拟线路有一个损坏，再次检查线路是否切换
|
||||
|
||||
```
|
||||
R1#traceroute 192.168.34.4
|
||||
Type escape sequence to abort.
|
||||
Tracing the route to 192.168.34.4
|
||||
VRF info: (vrf in name/id, vrf out name/id)
|
||||
1 192.168.12.2 5 msec 5 msec 5 msec
|
||||
2 192.168.32.3 1 msec 5 msec 5 msec
|
||||
3 192.168.34.4 1 msec * 1 msec
|
||||
```
|
||||
|
||||
## 7. 负载均衡
|
||||
|
||||
当去往同一个路由条目有多个出口的时候，并且管理距离和度量值都是一样的，也就是说路由器分辨不出来哪个路径好坏。路由器会将这些路线全部加到路由表中，进行等价负载均衡。
|
||||
|
||||
```
|
||||
R2(config)#ip route 100.0.0.0 255.0.0.0 192.168.12.1
|
||||
R2(config)#ip route 100.0.0.0 255.0.0.0 192.168.23.3
|
||||
R2(config)#do sh ip route
|
||||
.........
|
||||
S 100.0.0.0/8 [1/0] via 192.168.23.3
|
||||
[1/0] via 192.168.12.1
|
||||
........
|
||||
```
|
||||
|
||||
比如：100.0.0.0/8就有两个下一跳IP地址，并且都是`[1/0]`，所以全部加入了路由表，在发数据的时候，会将数据包一个IP地址发一个。可以通过如下命令查看下次往哪里走。
|
||||
|
||||
```
|
||||
R2(config)#do sh ip route 100.0.0.0
|
||||
Routing entry for 100.0.0.0/8
|
||||
Known via "static", distance 1, metric 0
|
||||
Routing Descriptor Blocks:
|
||||
192.168.23.3
|
||||
Route metric is 0, traffic share count is 1
|
||||
* 192.168.12.1 # 前面的*表示下一个IP包将发到这个地址
|
||||
Route metric is 0, traffic share count is 1
|
||||
R2#ping 100.1.1.1 repeat 1
|
||||
Type escape sequence to abort.
|
||||
Sending 1, 100-byte ICMP Echos to 100.1.1.1, timeout is 2 seconds:
|
||||
! # 100.1.1.1只有R1有，所以这次通了
|
||||
Success rate is 100 percent (1/1), round-trip min/avg/max = 2/2/2 ms
|
||||
R2#show ip route 100.0.0.0
|
||||
Routing entry for 100.0.0.0/8
|
||||
Known via "static", distance 1, metric 0
|
||||
Routing Descriptor Blocks:
|
||||
* 192.168.23.3 # 由于192.168.12.1上次才发过数据包，所以下次走192.168.23.3
|
||||
Route metric is 0, traffic share count is 1 # 这个是线路共享比例，等价负载均衡是1:1
|
||||
192.168.12.1
|
||||
Route metric is 0, traffic share count is 1
|
||||
R2#ping 100.1.1.1 repeat 1
|
||||
Type escape sequence to abort.
|
||||
Sending 1, 100-byte ICMP Echos to 100.1.1.1, timeout is 2 seconds:
|
||||
U # 100.1.1.1只有R1有，所以这次不通
|
||||
Success rate is 0 percent (0/1)
|
||||
```
|
||||
|
||||
负载均衡在企业的应用中非常的广泛，可以用于提升链路的可靠性，提升链路的速率。
|
||||
|
||||
Reference in New Issue
Block a user